中文字幕日韩人妻视频一区,99国产精品视频免费,久久热视频免费在线观看,日本高清二区不卡,91午夜激情视频在线看,国产综合一区二区三区av,成人久久久国产精品成人,日韩欧美素人丝袜视频,国产色av综合在线

Ventilation duct is a kind of ventilation and air conditioning engineering, which is made of metal, non-metal sheet or other materials. It is mainly used for air circulation. In some large places, ventilation duct has a wide range of applications, mainly in industrial and construction engineering, hotel, hotel, shopping mall, factory and office building central air conditioning system. Xiao Bian summarized the performance index of Shandong ventilation pipeline for you, looking forward to your attention.

1、工作壓力：系統風管總風管處設計的大的工作壓力。

1. Working pressure: the large working pressure designed at the main air duct of the system.

2、允許漏風量：按風管系統類別所規定平均單位面積、單位時間內的大允許漏風量。

2. Allowable air leakage: large allowable air leakage per unit area and per unit time according to the category of air duct system.

3、漏風量：通風管道系統中，在某一靜壓下通過風管本體結構及其接口，單位時間內泄出或滲入的空氣體積量。

3. Air leakage: the volume of air leaked or infiltrated per unit time through the structure and interface of the air duct body under a certain static pressure in the ventilation duct system.

濟南通風管道強度高、剛性好，通風阻力小，適應于各種領域。為了保障工業及民用建筑的正常通風，通風管道必須滿足高性能、長使用壽命的要求，這對其加工材質就有了較高的要求。一般鋼板、鍍鋅板、不銹鋼材質在通風管道制作中比較常用。如果你想對通風管道進行更深入的了解，歡迎經常來訪本站。

Jinan ventilation pipeline has high strength, good rigidity and small ventilation resistance, which is suitable for various fields. In order to ensure the normal ventilation of industrial and civil buildings, the ventilation pipe must meet the requirements of high performance and long service life, which has higher requirements for its processing materials. General steel, galvanized steel, stainless steel materials are commonly used in the production of ventilation pipes. If you want to have a deeper understanding of ventilation ducts, you are welcome to visit our website frequently.

濟南通風管道制作前的準備工作：

The preparation work before the manufacture of Jinan ventilation pipe is as follows

1、制作風管前，首先要檢查采用的材料是否符合質量要求，是否有出廠合格證明書或質量鑒定文件。若無上述證明文件則應進行外觀檢查，并應符合下列要求：

1. Before making air duct, it is necessary to check whether the materials used meet the quality requirements and whether there are factory certificates or quality appraisal documents. If there is no such certificate, visual inspection shall be conducted and the following requirements shall be met:

(1)板材表面應平整，厚度應均勻，無凸凹及明顯的壓傷現象，并不得有裂紋、砂眼及、刺邊和銹蝕情況;

(1) The surface of the plate shall be flat, the thickness shall be uniform, and there shall be no convex concave and obvious crush, cracks, sand holes, burrs and corrosion;

(2)型鋼應該等型、均勻，不應有裂紋、氣泡、窩穴及其它影響質量的缺陷;

(2) The section steel shall be of equal shape and uniform without cracks, bubbles, pits and other defects affecting the quality;

(3)其它材料不能因具有問題導致成品強度的降低或影響其使用效能。

(3) Other materials should not reduce the strength of the finished product or affect its use efficiency due to problems.

2、風管和配件表面平整、圓弧均勻、縱向接縫應錯開;咬口縫應緊密，寬度均勻。焊縫應作外觀檢查，不應有氣孔、砂眼、夾渣、裂紋等缺陷，焊接后鋼板的變形應矯正。

2. The surface of air duct and accessories shall be smooth, the arc shall be uniform, and the longitudinal joints shall be staggered; The bite joint shall be tight and uniform in width. The weld shall be inspected visually, and there shall be no air hole, sand hole, slag inclusion, crack and other defects. The deformation of steel plate after welding shall be corrected.

3、制作金屬風管和配件，外徑或外邊長的允許偏差，其中制作法蘭，圓形法蘭內徑或矩形法蘭內邊尺寸允許偏差為+2㎜，不平度不應大于2㎜。

3. The allowable deviation of outer diameter or outer edge length for manufacturing metal air duct and fittings is + 2mm for manufacturing flange, inner diameter of circular flange or inner edge size of rectangular flange, and the unevenness shall not be greater than 2mm.

4、風道系統內所有直角轉彎處均安裝消聲彎頭，消聲彎頭內設鍍鋅鐵板導流片。

4. All right angle bends in the air duct system are installed with silencing elbows, and galvanized iron sheet deflectors are set in the silencing elbows.